Landing impact studies of a 0.3-scale model air cushion landing system for a Navy fighter airplane

An experimental study was conducted in order to determine the landing-impact behavior of a 0.3-scale, dynamically (but not physically) similar model of a high-density Navy fighter equipped with an air cushion landing system. The model was tested over a range of landing contact attitudes at high forward speeds and sink rates on a specialized test fixture at the Langley aircraft landing loads and traction facility. The investigation indicated that vertical acceleration at landing impact was highly dependent on the pitch angle at ground contact, the higher acceleration of approximately 5g occurring near zero body-pitch attitude. A limited number of low-speed taxi tests were made in order to determine model stability characteristics. The model was found to have good pitch-damping characteristics but stability in roll was marginal

TRENDS IN FOOD DISTRIBUTION

The authors present a very detailed and all-inclusive report on the shifting frontiers of food distribution, focusing on the challenges facing the food store operator and the wholesale food distributor during the decade of the Seventies.Agribusiness,

Influence of Tire Tread Pattern and Runway Surface Condition on Braking Friction and Rolling Resistance of a Modern Aircraft Tire

A series of taxiing tests was conducted at the Langley landing loads track with both braked and unbraked (freely rolling) single and tandem wheels equipped with 32x8.8 type VII aircraft tires of different tread designs to obtain data on tire and braking characteristics during operation on dry and on contaminated concrete and asphalt run ways. Contaminants used were water, slush, JP-4 jet fuel, and organic and detergent fire-extinguishing foams. Forward velocities for the tests ranged from approximately 13 to 104 knots. Vertical loads of approximately 9,000 to 22,000 pounds and tire inflation pressures of 85 to 350 pounds per square inch were used. Results indicated that the unbraked tire rolling resistance increased with increasing forward velocity on dry and on contaminated runway surfaces. Peak tire-ground friction coefficients developed during wheel braking decreased rapidly with increasing velocity on contaminated runways but remained relatively unchanged on dry runways as the forward velocity was increased. Dry-runway friction coefficients were found to be relatively insensitive to tire tread pattern. However, the magnitude of the friction coefficients developed by tires on contaminated runways was extremely sensitive to the tire tread pat tern used, with circumferential-groove treads developing the highest values of friction coefficient, and smooth and dimple treads the lowest values for the tread patterns and runway conditions investigated

Experimental and analytical dynamic flow characteristics of an axial-flow fan from an air cushion landing system model

An investigation was conducted to compare the steady-state and dynamic flow characteristics of an axial-flow fan which had been used previously as the air supply fan for some model air cushion landing system studies. Steady-state flow characteristics were determined in the standard manner by using differential orifice pressures for the flow regime from free flow to zero flow. In this same regime, a correlative technique was established so that fan inlet and outlet pressures could be used to measure dynamic flow as created by a rotating damper. Dynamic tests at damper frequencies up to 5 Hz showed very different flow characteristics when compared with steady-state flow, particularly with respect to peak pressures and the pressure-flow relationship at fan stall and unstall. A generalized, rational mathematical fan model was developed based on physical fan parameters and a steady-state flow characteristic. The model showed good correlation with experimental tests at damper frequencies up to 5 Hz

Contemporary accounting, a refresher course for public accountants;

https://egrove.olemiss.edu/aicpa_guides/1033/thumbnail.jp

Comparing Two Sources of Retail Meat Price Data

The livestock industry uses information on meat prices at different stages in the marketing system to make production decisions. When grocery stores began using electronic scanners to capture prices paid for meat, it was assumed that the livestock industry could capitalize on having these point-of-sale data available as a measure of the value of its products. This report compares scanner price data with publicly available data collected by the U.S. Department of Labor’s Bureau of Labor Statistics (BLS). Of the two data types, scanner data provide more information about retail meat markets, including a wider variety of meat-cut prices, multiple measures of an average price, the volume of sales, and the relative importance of discounted prices. The scanner data sample, however, is not statistically drawn, and complicated processing requirements delay its release, which makes scanner data less useful than BLS data for analyzing current market conditions.price spreads, meat, meat pricing, scanner data, retail prices, retail meat prices, farm-to-retail, Agricultural and Food Policy, Agricultural Finance, Livestock Production/Industries, Marketing,